List of Electric Fireplace Error Codes (Furrion 88, E1, E3)
One thing about having an electric fireplace in your RV, it makes your trailer, etc., feel like you are in your traditional home. It is a grand feeling when you are out on the road and makes one more comfortable. However, electric fireplaces are devices and devices can fail
There are not that many error codes for an electric fireplace. There is an E1, E2, E5, and an 88 but with so few parts, more codes are not needed. What this lack of error codes does is make repairing the situation a lot simpler. Your owner’s manual may have more codes depending on the maker of the fireplace.
To learn more about these codes and what they mean, just continue to read our article. It has the information you want to know about so you can make the right repairs. Or have them done for you while the fireplace is still under warranty.
Fireplace Error 101
List of Electric Fireplace Error Codes
E1- There may be a loose wire on the thermal cutoff switch. This loose wire caused the infrared heater to either overheat or not work.
E3- The overheat sensor has been turned on. The only way this error code is supposed to flash or turn on is when all air inlets or outlets have been blocked.
E5- There is a problem with the fan or the vents. Usually, it is the fan that is not working properly and the blades are not spinning freely. There may also be a voltage issue causing the fan to not work.
#88- For Furion, this flashing code or steady light means that the blower fan is overheating. It could be a blocked inlet or vent causing the problem.
In most cases, you can do the repair yourself if your fireplace is not under warranty. Simply unblock the inlets and vents to see if that solves the problem. If not you can clean your fan and move it slightly so that there is more airflow.
Or you can follow what the manual says and reset the fireplace by unplugging it for about a half hour.
Furrion Fireplace 88 Code
This seems to be a common problem as more than one customer has seen this error code flashing in front of their eyes. All it means is that the blower fan is overheating and you need to take the right repair steps to get the error code off the screen and your fireplace working again.
The first step in the repair is to check your inlets and vents. If they have an obstruction then the airflow is blocked and cannot cool your fan down. If that doesn’t work, then you can reset the circuit board by turning the fireplace off for 15 to 20 minutes.
Keep in mind that these fireplaces are not a furnace replacement. They should not be used full time or as the main heating source. When you are camping in 40 degree F temperatures or lower, it is best to have a real furnace to handle the heating chores.
What Does E1 Mean On An Electric Fireplace?
While some repairmen may say that there is a loose wire or a wiring problem, usually, the E1 code means that your circuit board has failed. There has been some sort of damage to it or the board simply malfunctioned.
The bad news in all of this is that the circuit board is not designed to be repaired. You must get a new one and replace the damaged one as quickly as possible. The board is on sale in various places and can be bought fairly easily.
Or you have to have the manufacturer replace it if the fireplace is still under warranty. Never do any repair work while your devices, including these fireplaces, are still under warranty coverage.
Electric Fireplace Error Code E2
Depending on the manufacturer, the E2 error code is telling you that there may be something wrong with the temperature controller’s internal clock. There is supposed to be a memory chip inside the controller that stores different bits of data.
When there is a malfunction then this data cannot be retrieved and put into proper operation. The source for this problem could be static shock or the memory chip failed in some way.
To resolve this issue, try resetting the controller and if that doesn’t work, you will have to replace the controller. Your owner’s manual should have more detailed information available to help guide you through this repair. Or talk to a reputable mechanic that is experienced in electric fireplaces
Electric Fireplace Error Code E5
As stated earlier, the E5 error code has more to do with the fan than anything else. or there may be some sort of blockage in the vents keeping the hot air inside the fireplace.
When you see the E5 code, you need to check those two items right away. If it is a vent that is blocked then you just have to remove the obstruction. Not a big deal. If it is the fan that is overheating, you need to check to see if the blades are rotating normally.
If there is no obstruction, then you have to do a power reset and let the device solve its own problem. If that doesn’t work, contact the company that made the device.
Electric Fireplace Error Code CO
Modern technology has found a way to monitor different electronic and gas devices. it has developed sensors to watch over the different operating systems to make sure nothing is going wrong behind the scenes.
However, not every electronic device works smoothly and problems do arise. When they do, those sensors trigger error codes. Each code is designed to identify the source or possible source of the problem.
The key to getting your device working again will be to know and understand what those codes mean. Once you learn those meanings, it is easier to track down the source of the problem and repair it.
The drawback to that plan is the warranty. If it is still valid, then do not touch the device and let the authorized repairman handle the repair. Even if it is a simple repair.
What Does E3 Mean on My Electric Fireplace?
It is the code telling you that the fireplace or one of its components is overheating. The overheating sensor has been turned on as it has detected too much heat around your fireplace’s interior.
The only way your fireplace can overheat is if there is an obstruction in the vents or inlets. Those obstructions can be something like the fireplace is too close to a wall or as simple as dirt, dust, and debris have found their way to that inlet or vent.
All you have to do is move the fireplace slightly so the airflow is returned. Or simply clean up the debris and unblock the vent or inlet. This is not a difficult error to correct.
Electric Fireplace Error Code E1
You may see this error code on the Graystone models of electric fireplaces. This code is not something that should be ignored when you see it pop up on your controller’s screen.
What it is telling you is that there is a damaged circuit board in the system and it needs to be replaced. Unfortunately, this is one of those components that have been made that cannot be repaired.
Replacement is your only option and you should contact either your RV dealer or the company that made the electric fireplace. When under warranty, they will be the only ones with a list of approved repairmen to handle this problem.
If it isn’t under warranty, then you are free to buy your replacement at any retail outlet and DIY or have someone do it for you.
Fireplace Insert Flashing
There is no specific error code when this takes place. The common source may be the batteries that are in the system. Usually, when the batteries go bad, your fireplace will continually beep until the bad batteries are replaced with good ones.
There is another meaning to the term flashing. it is applied when installation is used for different items. The meaning of the word flashing refers to the thin metal pieces that go around the fireplace or other device to make it look nice.
The flashing is like paint and hides multiple construction sins but at least you have something good to look at. Also, the flashing protects your fireplace from spills, dropped items, and other harmful things like dust, dirt, and debris.
When the flashing gets bent or damaged, the only real option you have is to replace it. Trying to hammer out dents etc., does not work and only makes the flashing look worse.
Tec Flame Fireplace Manual
We found a couple of manuals but they are not under the name Tec Flame. There is one under Greystone’s brand name called Tec Flame but you only see the Greystone brand. You can find that manual at this link.
Then there is a Flame Tec option and these could be the same thing as the manual above. We will give you the company’s website link so you can contact them for a manual. That link is found here.
Also, you can check the different discussion forums for your specific brand of RV or travel trailer. They should have links to the model of the fireplace you own.
Downloading The Everlight Fireplace EF15-25C Manual
This link seems to have every manual you may need. You may have to do some searching to find it but according to the lead-in, the Everlight manual is there. Then there is this link. It has a variety of fireplace manuals ready to be downloaded.
You will have to scroll down a bit to get to the Everlight manual. Or you can contact the company that makes this brand of electronic fireplaces and see what they can send you.
Getting the manuals for different fireplaces is not that difficult and it should only take a basic search to come up with more options.
How do You Fix The ER Code on an Electric Fireplace?
The most important rule when rep[airing those error codes that pop up on you from time to time is if it is under warranty, DO NOT touch it. Companies are very strict about this and can and will void your warranty if you do something you are not supposed to do.
If you are not under warranty, simply look up what the error code means and repair the problem. If you do not like working with electricity get someone else to handle the problem.
How do I Reset My Electric Fireplace?
Modern technology has developed a simple method of resetting different electronic devices. For most electric fireplaces, all you have to do is turn the power off to the fireplace for 15 to 20 minutes.
Some brands may require a longer absence of power to reset their devices so look in your owner’s manual to see the specific time frame for your specific fireplace. If the reset method doesn’t work, then you may have to call in a repairman to diagnosis the problem and make the repair.
Some Final Words
Feeling at home in your RV is one important element in enjoying your camping time. One way to create that feeling is to install a nice electric fireplace. These handy devices provide some heat along with making you feel like you are back in your traditional home.
The key to using them is to not use them as a primary heat source when the temperatures drop at night. Use them to give you that back home feeling so you can relax and enjoy your evening.
